To begin we start by removing the wheel from the vehicle on the proper side that you want to change. Front Swaybar Installation. The front swaybar on the RX-8 consists of a series of brackets that hold it to the frame of the. Toyota Tacoma Tie Rod Change/Removal. And torque the endlink nuts to 40 ft-lbs and then torque the bracket bolts to 20 ft-lbs as well. Fastens the control arms to the steering knuckle. Frame connections and torqueing down the rear fastener to 130 ft-lbs and then the forward fastener to 130 ft-lbs as well. To install a new tie rod on a RX-8 you must first remove the old one from the vehicle. The next step is to reinstall the brake rotor and bracket. The RX-8 has two sets of front ball joints being the upper and lower ball joint. To install the new swaybar you will need to move it back into the place as the old one. Insert the stud of the new ball joint through the tapered hole of the knuckle and install either self-locking nut (self-locking nuts must always be replaced) or the slotted nut (also known as a castle nut) as supplied.
Included within these repairs. Secure dust boot and/or retaining ring (as applicable). Anyone here know the torque spec or know where I can look it up? 67-72 parts collector, . Back up the nut on the middle of the tie rod to ensure it does not move your alignment. The upper ball joint nut can be torqued to 41 ft-lbs. Jeep Grand Cherokee Front Swaybar Endlink to Arm Torque Spec: 100 ft-lbs. 04-15-2011, 10:28 PM||# 6|.
The upper ball joint only has one fastener that holds the ball joint onto the upper control arm. Lower arm please refer to that section on this web page. We encourage you to consult with a certified technician or mechanic if you have specific questions or concerns relating to any of the topics covered herein. Watch out for your cornhole! The frame bolts should be tightened down to 95 ft-lbs and the ball joint to 65 ft-lbs. Start by placing the hub into the. When putting the tie rod onto the vehicle the tie rod end nuts get tightened down to 80 ft-lbs. Hand tightened you can line up the bottom bolt hole and install the bolt and hand tighten its nut. If you want to replace just the outer portion of the tie rod you can remove the clamp bolts further down the tie rod and remove the outer portion of the rod and replace. Retired and Selling C10 Parts on the internet. The second connection is a rearward attachment via a nut. The new hub in reverse order from which it had been removed. Once loose the old hub should.
From here we can reinstall the wheel. RX-8 Upper Arm Frame Bolts Torque Spec: 95 ft-lbs. RX-8 Leveling bar endlink Torque Spec: 50 ft-lbs. Once you get the nut back in place you can torque it to 35 ft-lbs. If you choose to press out the ball joint you will need a ball joint pressing tool. First off it has a flag bolt and nut that connects it to the frame. If your talking about the little bolts that hold the joint to the a arm make them I have a torque wrench but tend to do things by feel..... also I feel like an AssHat...... Located in the center of the steering knuckle which allows for the front cv axle to come through and attach to the wheel hub using a similar single nut. Be sure to use a large enough torque wrench for this as that is a rather large amount of force. The lower bolts can be torqued down to 37 ft-lbs.
When tightening up the lower control arm fasteners be sure to set the wheel height to a level that it would be at during riding or when on the. If an AWD model be sure to hand tighen down the 3 wheel hub bolts and torque them down to 96 ft-lbs. Jeep Grand Cherokee 3. Essential repairs for the front end of this vehicle.
The most common one. And the steering knuckle. Access all special features of the site. If this is not the case, it's likely that the steering knuckle is worn and needs replacement. Installing the inner tie rod as well you will need a special tool to loosen and tighten.