There should be a diagram on the belt and that should tell you what pulley needs to go where. Be sure cover is fully seated on engine block dowels, engine block, and oil pan, before installing cover bolts. Received 0 Likes on 0 Posts. Lubricate front cover seal lip with engine oil, or petroleum jelly. This site uses cookies to store information on your computer to improve our website and to enable us to advertise to you those products which may be of interest to you. 5.7 hemi timing cover bolt diagram images. Any help is appreciated, thanks. Then install air conditioning condenser and power steering fluid cooler. Front Cover to Cylinder Block. Be sure seal contact surface of damper is smooth and free of burrs, nicks, or corrosion. Evacuate and recharge air conditioning system if necessary. Connect radiator upper and lower hoses. Loctite pipe sealing compound, to fastener that goes in hole ÒAÓ (Figure 2-30).
Install crankshaft pulley. Refer to sealer application diagram (Figure 2-27). Radio, Antenna, Speakers, DVD, and Video systems. Apply bead of anaerobic sealer, such as Loctite 510, to water pump and adapter plate.
I am putting on my fan/radiator/ and AC condenser today but figured I'd throw this out there to see if someone remembers a couple hidden spots I may be missing. 5.7 hemi timing cover bolt diagram 2017. Reason: add belt picture from youtube. By using the site, you're agreeing to cookies being used in line with our Cookie Policy. Install injection pump gasket on front cover studs (Figure 2-28:). Then lubricate seal contact surface of torsional damper with engine oil.
Drive gear mark should be at 12 o'clock position and driven gear mark. Timing mark on gear should be facing. Crankcase Ventilation. Parts like Timing System are shipped directly from authorized Mopar dealers and backed by the manufacturer's warranty. Install injection pump drive gear on camshaft (Figure 2-26). Hex Head Bolt And Coned Washer, Mounting. Early 392 hemi timing cover. Rotate pump to align if necessary. Then see if its making any sense with the bolt sizes you have.
At 6 o'clock position. Parts fit for the following vehicle options. Fill cooling system. Tighten baffle attaching bolts/nuts to 33 lb-ft (45 N. m) torque. Install baffle in front cover (Figure 2-29). Then install pump attaching nuts. Install radiator and shroud (Figure 2-21). Carpets, Floor Mats, Load Floor, and Silencers. 2007 Dodge Ram SLT 5.7 Hemi Timing cover and water pump bolt diagram. Wiper and Washer System. Wiring-Body and Accessories. Engine Identification, Service Engines & Engine Service Kits. Power Steering Pump Attachment.
Install torsional damper. Install front cover on engine block (Figure 2-28). C. Install and tighten driven gear attaching bolts to 13-20 lb-ft (18-27 N. m) torque. Connect battery negative cables. Be sure key is fully seated.
Rear Seats - Second Row Adjusters, Recliners, Shields and Risers. Purge air from cooling system (if necessary), and top off coolant level at surge tank. 0L V6 24V VVT Engine] TENSIONER BRACKET TO CYLINDER BLOCK, [3. NOTE: If timing marks are not perfectly aligned, turn the pump shaft to correct alignment. Instrument Panel Cluster. Timing cover and Water pump bolts | Page 2. Maybe someone has done this recently and can remember off the top of their head. I have some of the part numbers at home. Last edited by fj5gtx; 09-12-2020 at 05:59 AM. 7 Hemi Timing cover and water pump bolt diagram.
Hello everyone, This is clearly a long shot but putting back together my engine and had these bolts leftover once I put back on my timing cover, water pump, AC compressor, power steering, and alternator. Install fuel injection pump driven gear on pump shaft as follows: a. Align timing marks on drive and driven gears and install driven gear on pump shaft. B. Verify timing mark alignment. Power Distribution Center, Fuse Block, Junction Block, Relays and Fuses. Manifolds and Vacuum Fittings. Install coolant crossover and oil filler neck. Crankshaft, Piston, Drive Plate, Flywheel, and Damper. Tighten attaching nuts to 15-20 lb-ft (20-27 N. m). Duramax LLY - FRONT COVER AND TIMING CHAIN - Front Cover Installation. Tighten bolt to 140-160 lb-ft (190-217 N. m) torque. Power Steering Pump to Engine Block.
Refer to Figure 2-36 for sealer application. Check alignment of timing marks on front cover and injection pump flange. Use RTV-type sealer, such as Loctite 592, on oil pan and oil pan contact surface of front cover. Secure fuel injection pump to front cover. Upward (12 o'clock position). Then install damper attaching washer and bolt.