Everything looks good in the headlight too. The above text is right out of the manual. ATM I just want to eliminate the starting circuit cutoff relay all together is there any way to do this.
Continuity as follows. Hi everyone I have a 2000 r6 and am having problems starting it. The starting system. • The clutch lever is pulled to the handlebar (the clutch switch is closed) and the sidestand is up (the. My kickstand switch screws are seized on so instead of stripping them, I followed the line from the kickstand sensor up to where it connects, disconnected it and shorted it out (connected a wire between the two connectors) on the bike side. Btw if you end up replacing the speedo unit id like a chance to buy your old one for my 01 r6, im going to make it a track only bike and really only want the doesnt need to work and has to be taped off anyhow. The ecu I had flashed last fall and I don't remember be off the top of my head if I had it flashed with the pc5 configured into the system. Disconnect the starter relay from the coupler. The clutch lever is pulled to the handlebar (the. Thanks for any help. Got caught in a light rain day before. Measure the starting circuit cutoff relay for. Terminals as a shown. Jumping the solenoid only turns it over - no fire.
According to the manual, my starting circuit cutoff relay is bad, but I do not know where I can buy some new. If anyone can shine a little light my way I'd greatly appreciate it. I'm wondering if it matters or not? Can be started by pressing the start switch. The light in the cluster doesn't work either. I think I have traced it down to the relay assy for the saftey start circuit. Basically added a 1/8 inchpplate connecting stay to frame.... took almost 15 minutes.
Kill switch works as it should. On Saturday I started the bike up fine and was letting it warm up. Replace the starter. Ok first off let me say thanks ahead of time to anybody who takes the time to give much needed help to my problem at hand. STARTING CIRCUIT CUTOFF SYSTEM OPERATION. Check the entire starting system s wiring. 5 Engine stop switch. I'm trying to get to the track for the first time. It didn't go down nearly as hard as I did, but you never know. The starting circuit cutoff relay prevents the. If I put the bike into neutral & try to start it with the kickstand down it won't start, but if I pull up the kickstand it'll start right up. Replace the ignitor. Charged it all up and turned the key and all lights came on just fine but when I hit the starter button all I could hear was a clicking sound coming from what I am assuming is the starter relay? Check it with a VOM or jumper wires as a test to verify.
The starting circuit cut-off relay prevents the starter motor from operating when neither of these condi-. Did I ruin the electrical components with the running car even though the bike jump started fine? Go back to messagenet " imma newbie member lol" and make use of thier diagrams to find location of switch. Reset/"easy" button lol. Good luck hope this is helpful. I've checked the wire harness and all connections and plugs and the ground. I pulled the right side controls, cleaned up the kill switch contacts and starter button contacts. Starting circuit cutoff relay. I plan on fixing the upper fairing mount & testing all of the switches tomorrow. I need to make a continuity tester & then I'll find out if the LED in the gauge cluster is good & then I'll test the neutral switch. Starter motor from operating when neither of.
I also put a meter on all the wires at the controls and in the headlight. However, if it is activated bike doesnt start, and, shouldnt have anthing to do with neutral light. Is the starting system s wiring properly connected. So I should be able to just hook up the bare minum wires and make this bike run right like the red/blue wire to the pump, red/white, red/black wire etc. Anyway long story short, bike no longer will turn over at all. Battery positive terminal red/white. It seems like the 99-02 R6s have some wiring issues with things shorting out. Check the starting circuit cutoff relay for continuity. Does the starter relay have continuity between. Chart will be reversed. This should turn the starter with the switch. What do the experienced have to say? Tester positive probe red.
I've got a 07 r1 that is making my life difficult to say the least. I tried to start it again but all I heard was a click under the seat. Replace the neutral. It is showing code 43 on the gauges and im not getting the fuel pump to prime for start up. I posted this on the Facebook Clinic but was hoping to get some more input here... Just rebuilt starter. He had gotten me one, but it was a general maintenance manual, so it wasn't very helpful. NOTE: When you switch the and leads of the.
Think my man, if ya pull in the clutch it doesnt make the light come on ok? I have to put up the kickstand & find a certain spot when pulling in the clutch to get it to start.. . Sorry buddy but there is no. I'm hoping to get it up & running before long. I mean a relay is just a switch to turn off or on right? IGNITION SYSTEM ELEC. And the main switch is set to "ON" (both switches are closed), the. Refer to CIRCUIT DIAGRAM . 12 V) to the starter relay coupler as. I checked the clutch wires to headlight bucket and there are no breaks. WHEN THE TRANSMISSION IS IN. As for your current problem, check the wires plugging into the back of your speedo, also check wiring diagram to confirm which wire in speedo plug to check for batt.
It will either be unplugged"probably the case". When I turn the key and the kill switch is in the run position, usually I hear the fuel pump but there is nothing, even after cleaning the contacts. Went to start the bike to go home and nothing. Is the clutch switch OK? For the speedometer problem it pretty much says the problem is going to be the speed sensor.